DeWalt DW999 Manuál s instrukcemi Strana 8
- Strana / 36
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
7
English
hours to complete. Battery packs should be tuned up weekly or after
10 to 20 charge/discharge cycles or whenever the pack no longer
delivers the same amount of work.
1. To tune up your battery pack, place the battery in the charger as
usual. The red light will blink continuously indicating that the
charge cycle has started.
2. Press the Tune-Up™ Mode button any time after the charge cycle
has started. The red light will stop blinking momentarily, blink
quickly 3 times, and then resume blinking continuously. The
charger is now tuning up the cells in your battery.
3. When the Tune-Up™ mode cycle is complete, the light will stay on
continuously. The pack is fully charged and may be used at this
time or left in the charger.
4. If you select Tune-Up™ Mode and then change your mind,
remove the battery from the charger. After 5 seconds, insert the
battery into the charger. The normal charge cycle will begin.
Side Handle (Fig. 3)
A side handle (A) is supplied with this hammer. It clamps to the front of
the gear case as shown and can be rotated 360˚ to permit right or left
hand use.
CAUTION: Always use the side handle supplied with the tool.
Keep a firm grip on the tool at all times. Do not attempt to operate this
tool without holding it with both hands. Operating this tool with one
hand will result in loss of control. Breaking through or encountering
hard materials such as re-bar may be be hazardous as well.
Variable Speed Switch (Fig. 3-B)
To turn the tool on, squeeze the trigger switch. To turn the tool off,
release the trigger switch. Your tool is equipped with a brake. The
chuck will stop as soon as the trigger switch is fully released.
The variable speed switch enables you to select the best speed for a
particular application. The farther you squeeze the trigger, the faster
the tool will operate. Use lower speeds for starting holes without a
center punch, drilling in metals or plastics, driving screws and drilling
ceramics. For maximum tool life, use variable speed only for starting
holes or fasteners.
Battery packs should be tuned up after every 10th charge/ discharge
cycle or whenever the pack no longer delivers the same amount of
work. To use the automatic tune-up mode, simply place the battery
pack in the charger and leave it for at least eight hours. The charger
will cycle through the following modes.
1. The red light will blink continuously indicating that the 1-hour
charge cycle has started.
2. When the 1-hour charge cycle is complete, the light will stay on
continuously and will no longer blink. This indicates that the pack
is fully charged and can be used at this time.
3. Whenever the pack is left in the charger after the initial 1-hour
charge, the charger will begin the Automatic Tune-Up™ Mode.
This mode continues up to 8 hours or until the individual cells in
the battery pack are equalized. The battery pack is ready for use
and can be removed at any time during the Tune-Up™ Mode.
4. Once the Automatic Tune-Up™ Mode is complete the charger
will transition to a maintenance charge; no indicator light shows
the completion of the Automatic Tune-Up™ Mode.
Using the Manual Tune-Up™ Mode
The manual Tune-up™ mode equalizes or balances the individual
cells in the battery pack at its peak capacity. This mode takes up to 8
FIG. 3
A
C
B
D
- INSTRUCTION MANUAL 1
- GUIDE D'UTILISATION 1
- MANUAL DE INSTRUCCIONES 1
- SAVE THESE INSTRUCTIONS 2
- Rotary Hammers 3
- Battery Packs 4
- The RBRC™ Seal 4
- Pack (Fig. 1) 5
- Chargers 5
- Charging Procedure 6
- BATTERY PERFORMANCE 7
- Using Automatic Tune-Up™ Mode 7
- Important Charging Notes 7
- Side Handle (Fig. 3) 8
- Operation 9
- SDS Chuck (Fig. 3-D) 9
- CONSERVER CES DIRECTIVES 11
- Français 12
- EWALT de 18 volts. Lorsqu’on 14
- EWALT encourage ses 14
- EWALT ou chez un dépositaire 14
- Méthode de chargement 16
- Chargeurs 16
- CONSERVER CES MESURES 18
- Interrupteur (Fig. 3-B) 19
- Mandrin SDS (Fig. 3-D) 19
- Fonctionnement 20
- Jauge de profondeur 21
- Entretien 21
- Accessoires 21
- Réparations 21
- Garantie complète 22
- CONSERVE ESTAS INSTRUCCIONES 23
- EWALT para que 25
- Baterías 26
- El sello RBRC™ 26
- (Fig. 1) 27
- Cargadores 28
- Procediemente de Carga 28
- El usar automático Templa-Up™ 30
- Utilización del modo Tune-up 30
- Mango lateral (Fig. 3) 31
- Interruptor (Fig. 3-B) 31
- Broquero SDS (Fig. 3-D) 31
- (Fig. 4) 32
- Operación 32
- EWALT u otras organizaciones 33
- Garantía Completa 34
- EWALT S.A. DE C.V 35
- Copyright © 2003 36
Související produkty a manuály pro Elektrické vrtačky DeWalt DW999
Elektrické vrtačky DeWalt D25213K Servisní příručka
(140 stránky)
(140 stránky)
Elektrické vrtačky DeWalt DCD940 Servisní příručka
(200 stránky)
(200 stránky)
Elektrické vrtačky DeWalt DC720 Uživatelský manuál
(16 stránky)
(16 stránky)
Elektrické vrtačky DeWalt DW005 Servisní příručka
(116 stránky)
(116 stránky)
Elektrické vrtačky DeWalt DCD945 Uživatelský manuál
(20 stránky)
(20 stránky)
Elektrické vrtačky DeWalt DC987 Servisní příručka
(20 stránky)
(20 stránky)
Elektrické vrtačky DeWalt DWD010 Uživatelský manuál
(16 stránky)
(16 stránky)
Elektrické vrtačky DeWalt DW979 Manuál s instrukcemi
(34 stránky)
(34 stránky)
Elektrické vrtačky DeWalt DWD014 Servisní příručka
(36 stránky)
(36 stránky)
Elektrické vrtačky DeWalt D25313 Uživatelský manuál
(24 stránky)
(24 stránky)
Elektrické vrtačky DeWalt DWD024 Servisní příručka
(40 stránky)
(40 stránky)
Elektrické vrtačky DeWalt DW505 Manuál s instrukcemi
(22 stránky)
(22 stránky)
Elektrické vrtačky DeWalt DW926 Servisní příručka
(100 stránky)
(100 stránky)
Elektrické vrtačky DeWalt DCD710 Servisní příručka
(40 stránky)
(40 stránky)
Elektrické vrtačky DeWalt D25003 Uživatelský manuál
(20 stránky)
(20 stránky)
Teledyne-lecroy WaveExpert 9000_NRO9000_SDA100G Getting Started Ma manuals
Owner’s manuals and user’s guides for Equipment Teledyne-lecroy WaveExpert 9000_NRO9000_SDA100G Getting Started Ma.
We providing 1 pdf manuals Teledyne-lecroy WaveExpert 9000_NRO9000_SDA100G Getting Started Ma for download free by document types: User Manual
Komentáře k této Příručce